Technician I - Component Specialist

701 Blue Ridge Rd, Raleigh, NC 27606, USA Req #1226

Friday, May 3, 2024

PRIMARY FUNCTION :

The primary function of this position is to perform component repairs and rebuilds, primarily on engines, transmissions and torque converters.

ESSENTIAL DUTIES:

• Check the equipment and supplies required to perform the work scheduled, comply with PPE requirements, and otherwise prepare for duties.
• Uses manuals, repair manuals, parts manuals, parts diagrams to troubleshoot components
• Uses lift trucks, overhead cranes, & other aides to lift or move components into position to be repaired.
• Uses hand & power tools to disassemble, re-build, repair, & test components.
• Uses miscellaneous resources and computers to reference parts, get information about parts & enter data into record systems.
• Uses tools to disassemble/re assemble parts or equipment; cleans parts with rags, cleaners, power washer; uses test equipment to make diagnostic checks; and controls powered equipment or tools to make repairs.
• Uses power washers & spray paint equipment to clean components
• Uses test benches and dynamometer to test completed components.

MINIMUM REQUIREMENTS :

Education :

Must have a high school education or GED.

Work Experience :

Requires up to two years schooling or direct work experience; Must be mechanically inclined and have good basic knowledge obtained through schooling or work experience.

Physical :

Must be able to daily and repeatedly stoop, kneel, bend and climb beside, onto and underneath various equipment to perform diagnosis and repairs; Must be able to effectively see to perform repairs, research technical manuals, and develop written repair work order reports. Must be able to routinely and physically lift/position various parts to perform repairs/service and manually handle parts up to 112 pounds, as well as use mechanical hoist for heavier parts.

Other :

Must be able to effectively write repair activities on customer work orders; Must have cognitive reasoning and problem-solving skills to apply knowledge, written information and verbal instructions in repairing/servicing unusual and/or unknown technical equipment operational problems; Should have exposure to P.C. base equipment and parts information; Capable of learning and understanding technical information, service manuals and reports;

This is a four day a week, 10 hour a day position. The hours are 6:00 am - 4:30 pm. Overtime is required.

This job description is not intended to be all-inclusive. Your supervisor may request and assign you similar duties. Any major modification of this job role requires Human Resources approval.

Gregory Poole Equipment Company is an Equal Opportunity/Affirmative Action employer and will consider all qualified applicants for employment without regard to race, color, religion, gender, sexual orientation, gender identity, national origin, age, protected veteran status, or disability status.

Other details

• Pay Type Hourly
• Required Education High School

Apply Now

initStaticMap(true); PRIMARY FUNCTION:\n \nThe primary function of this position is to perform component repairs and rebuilds, primarily on engines, transmissions and torque converters.\n \nESSENTIAL DUTIES:\n\nCheck the equipment and supplies required to perform the work scheduled, comply with PPE requirements, and otherwise prepare for duties.\nUses manuals, repair manuals, parts manuals, parts diagrams to troubleshoot components\nUses lift trucks, overhead cranes, & other aides to lift or move components into position to be repaired.\nUses hand & power tools to disassemble, re-build, repair, & test components.\nUses miscellaneous resources and computers to reference parts, get information about parts & enter data into record systems.\nUses tools to disassemble/re assemble parts or equipment; cleans parts with rags, cleaners, power washer; uses test equipment to make diagnostic checks; and controls powered equipment or tools to make repairs.\nUses power washers & spray paint equipment to clean components\nUses test benches and dynamometer to test completed components.\n\n \nMINIMUM REQUIREMENTS:\n \nEducation:\nMust have a high school education or GED.\nWork Experience:\nRequires up to two years schooling or direct work experience; Must be mechanically inclined and have good basic knowledge obtained through schooling or work experience. \n \nPhysical:\nMust be able to daily and repeatedly stoop, kneel, bend and climb beside, onto and underneath various equipment to perform diagnosis and repairs; Must be able to effectively see to perform repairs, research technical manuals, and develop written repair work order reports. Must be able to routinely and physically lift/position various parts to perform repairs/service and manually handle parts up to 112 pounds, as well as use mechanical hoist for heavier parts.\n \nOther:\nMust be able to effectively write repair activities on customer work orders; Must have cognitive reasoning and problem-solving skills to apply knowledge, written information and verbal instructions in repairing/servicing unusual and/or unknown technical equipment operational problems; Should have exposure to P.C. base equipment and parts information; Capable of learning and understanding technical information, service manuals and reports; \n \nThis is a four day a week, 10 hour a day position. The hours are 6:00 am - 4:30 pm. Overtime is required.\n \n \nThis job description is not intended to be all-inclusive. Your supervisor may request and assign you similar duties. Any major modification of this job role requires Human Resources approval. \n \n \n